-
When This Checklist Makes Sense
-
Step 1: Check the harness webbing (not just the label)
-
Step 2: Inspect the carabiner like it's the only thing between you and the ground
-
Step 3: Test the lanyard and shock absorber
-
Step 4: Verify the anchor point and connection hardware
-
Step 5: Don't skip the footwear (this is the step most people overlook)
-
Step 6: Cross-reference with the Miller fall protection website
-
Step 7: Document everything—including what you replaced
-
Two Mistakes That Trip People Up
-
Why I Won't Help You With Your Fire Alarm
When This Checklist Makes Sense
I coordinate emergency fall protection orders for industrial clients—construction crews, warehouse operations, manufacturing facilities. In six years, I've handled more than 200 rush requests, including 47 in the last quarter alone. About a third of those calls start with some version of "I need this by tomorrow morning."
This checklist is for safety managers, crew leaders, and anyone responsible for pre-shift PPE verification. Seven steps. Twenty minutes if you actually do them in order.
One thing before we start: if you landed here looking for fuzzy handcuffs or how to get a fire alarm to stop beeping, you're on the wrong page. (I'll come back to that at the end—it's more relevant than it sounds.)
Per OSHA's general industry fall protection standard (1910.140), personal fall protection systems must be inspected before each use and after any fall event. The standard doesn't tell you how to do it—that's what this checklist is for.
Step 1: Check the harness webbing (not just the label)
Run the webbing through your hands. You're feeling for fraying, cuts, abrasion, or stiffness. Any of those means the harness comes out of service.
Pay close attention to the stitching at load-bearing points: the chest connection, shoulder straps, leg loops. Loose or broken stitching is a hard stop—no exceptions, no "but it still looks okay."
The label matters, but it's not enough. I've seen harnesses with clean, legible tags and compromised webbing (the tag survived; the nylon didn't). Trust your hands more than the label.
Step 2: Inspect the carabiner like it's the only thing between you and the ground
This is where I see the most skipped checks. A Miller fall protection carabiner is precision hardware, and it fails differently than webbing does.
Check three things:
- The gate. Does it open and close smoothly? Does it lock without forcing it?
- The body. Look for cracks, corrosion, or deformation—especially at the nose and spine.
- The markings. You need to see the load rating, manufacturer, and traceability code. If the stamp is worn away, you can't verify the rating. And if you can't verify it, you can't trust it.
One thing most people miss: open the gate and look at the locking mechanism inside. Grit, rust, or dried lubricant can make a carabiner feel fine when it's actually one shift away from failing open.
Even after swapping a suspect carabiner, I've second-guessed myself. What if the gate had been damaged in a way that didn't show up visually? In one case, we pulled the whole lanyard assembly and started fresh. It cost more than it probably needed to—but I slept better that week.
Step 3: Test the lanyard and shock absorber
Stretch the lanyard out. Look for cuts, burns, or glazing (that shiny, melted look from heat exposure). Check the shock absorber pack—it should be intact and unexpanded.
If the shock absorber has deployed, the lanyard is done. No exceptions. It did its job; now it's spent. Trying to "get one more use" out of a deployed shock absorber is how people get hurt.
Same gate test for the snap hooks or connectors on both ends. Same logic.
Step 4: Verify the anchor point and connection hardware
This step is about the system, not just the components. A perfect harness connected to a bad anchor point is still a fall waiting to happen.
Look at the anchor: is it rated? Is it marked? Is the connection point at the right height per your fall protection plan? If you're not sure, find the original installation documentation. If the documentation is missing, that's a flag—not necessarily a dealbreaker, but a flag.
I've seen crews install a brand-new Miller harness system on an anchor point that hadn't been inspected since 2011. The gear was flawless. The anchor was questionable. The whole setup was only as strong as its weakest piece.
Step 5: Don't skip the footwear (this is the step most people overlook)
I get it. This is a fall protection checklist. Why are we talking about boots?
Because a fall isn't the only hazard on a site. Dropped tools, shifting materials, and uneven surfaces cause their own injuries. If your crew wears metatarsal boots, check the condition of the metatarsal guard—cracked or deformed guards offer almost no protection.
In March 2024, a client called because a crew member's metatarsal boot failed after a dropped wrench. The guard had a visible crack that nobody caught during daily checks. They ordered replacements that afternoon. The lesson: "full PPE inspection" means the whole system, not just the gear that goes on your torso.
This is the step people skip most often. Don't be those people.
Step 6: Cross-reference with the Miller fall protection website
If you're unsure whether a piece of gear is compatible with your system, look it up. The Miller fall protection website has model-specific inspection guidance, replacement schedules, and compatibility charts.
When I first started sourcing gear, I assumed "rated for the same load" meant "works together." A few compatibility issues later, I learned that load rating is the floor, not the ceiling.
This takes five minutes and prevents the classic mistake: mixing components from different systems because they "look like they should work together."
Honestly, most reputable manufacturers publish this information. I mention Miller specifically because their documentation is thorough and easy to navigate—which matters when you're doing this at 6 a.m. before a shift and your coffee hasn't kicked in yet.
Step 7: Document everything—including what you replaced
Write down what you inspected, what you found, and what you did about it. If you replaced a carabiner, note the model number and date. If you pulled a harness from service, note why.
This sounds like paperwork. It is paperwork. But it's the kind that protects you during an audit and helps you spot patterns. "We're replacing the same lanyard every eight months" might mean something in the environment is degrading it faster than expected. Without documentation, you'd never notice.
After the third time we replaced the same model of lanyard for the same client, we finally asked what was happening on their end. Turned out they were storing the gear next to a heat source. Two years of replacements, solved by moving a shelf. The documentation got us there.
Two Mistakes That Trip People Up
Mistake #1: Inspecting the gear but not the system. A carabiner can pass every individual check and still be the wrong carabiner for your configuration. Make sure all components are rated to work together.
Mistake #2: Assuming "new" means "inspected." I've unboxed harnesses with twisted webbing and carabiners that didn't lock smoothly. New gear gets inspected too. No exceptions, regardless of what the shipping label says.
Why I Won't Help You With Your Fire Alarm
Earlier I said this page won't help with fire alarms or fuzzy handcuffs. That was partly a joke—but only partly.
In six years of coordinating emergency orders, the suppliers and specialists who've earned my trust are the ones who drew a clear line around what they do well. One vendor told me flat-out: "We can't hit your timeline—here's someone who can." We've used them for every non-rush order since.
Fall protection is a narrow, technical category. Getting it right means understanding load ratings, inspection cycles, and how components interact across an entire system. That's the job. Fire alarms and handcuffs are someone else's job—and I'd bet they feel the same way about carabiners.
If you're running this checklist and something fails, or if you need gear fast, check the Miller fall protection website for model-specific guidance first. Then call a supplier who knows the product line. The twenty minutes you spend inspecting is cheaper than the alternative—and the alternative usually involves paperwork nobody wants to file.